Hong Kong Bearing Group Limited

Common faults of rolling bearing and prevention methods

Apr 10, 2023

The rolling bearing in normal operation should be uniform, light, no block and no loose shake when it is rotated by hand. The operating temperature is not more than 70 ℃. When the metal rod is used, it makes an even sound of "rustling" without vibration. The most common fault of the rolling bearing is a serious fever. If it is newly installed or cleaned after oil change, it quickly warms up and has a serious fever as soon as it runs, but there is no abnormal sound or vibration in the operation. The reason is very likely to add too much grease, should only be loaded with the appropriate amount of grease. At the same time of a serious fever, if the bearing is also found to be "stuck", the possible reason is that the bearing cover of the two shafts is too tight to the outer ring of the bearing, and the axial clearance is not set aside enough in accordance with the provisions, and the temperature rise in operation causes the shaft to extend.
In individual cases, the inner ring of ball bearing and shaft are fitted too tightly, so that the inner ring expands, or the bearing seat and the outer ring of bearing are fitted too tightly, so that the inner ring expands, or the bearing seat and the outer ring of bearing are fitted too tightly, so that the outer ring is compressed and deformed. For the former, we can first understand the assembly situation and whether the interference size is too large when machining the shaft. If so, although the ball bearing is hot installed, the assembly will be more difficult. At this time, the bearing can only be removed, the journal can be polished to the proper assembly size, and then assembled separately. The latter often occurs on the split bearing seat. If the screw of the bearing is loosened at this time, it will be found that the bearing becomes "flexible". You can add one or two layers of paper pad on the open surface of the bearing to eliminate the fault. Because, this kind of bearing seat is the first pad in the place of 0.1mm ~ 0.3mm thick paper pad, to process its inner hole, but cancel the paper pad, the hole will be flattened.
In addition, if there are dust particles, impurities with grease into the rolling bearing raceway, it is also possible to appear stuck phenomenon. Once this happens, the oil should be cleaned and changed. When repairing, even good quality clean grease should be carefully inspected before it can be used. If the fever appears in the rolling bearing has been running normally for a period of time, dry friction noise, or irregular crash sound occurs when the metal rod is touched, it may be a lack of oil or oil has not been clean, it may also be the rolling part of the bearing is damaged, should be dismantled and cleaned, carefully checked, oil change or disassembly bearing. The rolling part of the bearing has a defect and must be replaced.
1 Corrosion
Bearing out of operation by moisture or water in the oil, so that the surface of the rolling body or raceway appear rust or rust.
2 Indentation
When the hard material into the raceway, often in the raceway or rolling body surface pressure pits. At this time, not only in the operation of noise or crash, too large pits will also produce vibration and bearing serious fever.
3 Bearing ring is broken
In addition to the material and heat treatment and other manufacturing reasons, if the interference size of the shaft is too large, the assembly method is improper, it will also burst and damage the inner and outer rings of the bearing. Improper shoulder design of thrust bearing will also cause the moving ring to be crushed. To this end, in addition to the replacement of new bearings, the reasons should be identified. Exclude.
4. Fatigue stripping of raceway surface
This is normal wear and tear, but if not used properly, this wear and tear will accelerate rapidly.
5 Cage fracture
It's basically a matter of material and manufacturing. Sometimes, the cage is injured during installation, and it may also cause premature fracture. New bearings should be replaced.
6 The rolling body is broken
There will be larger noise and even vibration during operation. Most of the reasons are due to improper material or heat treatment, so we have to replace it.
7 Current corrosion
In electric welding, if the current passes through the bearing, the contact between the rolling body and the raceway will fever, produce sparks, local burns and leave "scars". Therefore, when welding, it is necessary to make the welding "ground wire" as close as possible to the welding point, in any case, do not allow welding current through the bearing.

goTop