Hong Kong Bearing Group Limited

How To Choose The Right Bearing Grease

Mar 28, 2024

How to choose the right bearing grease

 

In the industrial field, grease is a commonly used lubricating material that can effectively extend the service life of bearings and reduce friction and wear. However, there are many types of grease, and how to choose the grease that suits you is the key we need to understand.

 

Types of grease

 

1. Calcium-based grease: suitable for machines under low-speed, low-temperature, and medium-load conditions. It has poor water resistance and is not suitable for use in humid environments.

 

2. Lithium-based grease: suitable for heavy-duty, high-speed machines, with good wear resistance and water resistance, and also suitable for use under high temperature conditions.

 

3. Potassium-based grease: suitable for machines used under high temperature and high load conditions. However, it is not as sealing and water-resistant as lithium-based grease.

 

4. Multi-thick grease: suitable for machines with high load, low speed, heavy load, large impact and large vibration. However, oil separation may occur at high temperatures.

 

5. Polyurethane grease: suitable for extremely low temperature conditions (to -50°C). However, the friction coefficient is very high, so it is not suitable for high-speed rotating machines.

 

Bearing grease selection principles

 

1. Working environment

It mainly refers to the minimum and maximum temperature of the working environment, air humidity, whether it contains corrosive gases or excessive dust, etc. For example, when used outdoors in severe cold areas, lithium-based low-temperature grease should be used; calcium-based grease should be used in places with high humidity and water; in dry places with less water, sodium that is easily soluble in water should be used. base grease.

 

2. Working temperature

One is the lowest temperature of the use environment, and the other is the highest temperature that may occur during operation. When the operating temperature is high, high-temperature grease with a higher dropping point should be selected. The actual maximum operating temperature should be 10-20C lower than the grease dropping point (synthetic grease should be 20 ~ 30C).

 

3. Load conditions

For heavy loads, grease with a smaller taper should be used. When working under high pressure, in addition to requiring a small cone angle, it also requires high oil film strength and extrusion performance.

 

Bearing grease filling amount

 

1. The impact of grease injection amount on bearing use

For sealed bearings, appropriate grease has been filled during production; for open bearings, although a sealing device is installed to prevent grease leakage, it will still gradually decrease due to a small amount of leakage and other reasons during use, and needs to be carried out. Keep replenishing.

Practice has proved that the amount of grease injected into the bearing will have a certain impact on its operation. Too little grease injection can easily lead to insufficient lubrication. In severe cases, it can lead to dry friction, generate high heat, and cause the bearing to be scrapped in a short period of time due to wear, which may have a serious impact on the entire equipment. If the amount of grease injected is too much, the rolling resistance of the bearing rolling elements will be large, and the temperature of the grease in the bearing will be high. When it reaches its dropping point, it will turn into liquid and be lost. Finally, the serious consequences of too little grease injection will occur. In addition, Leaking grease causes waste and pollutes the environment.

 

2. Principles of fat injection amount

The principle of grease injection: the less the better while ensuring sufficient lubrication of the bearing.

Based on practical experience, the following principles are more appropriate.

For open bearings, the appropriate amount of grease injection should depend on the cavity volume of the bearing chamber (after the two bearing caps and the bearing are installed, the portion of the air contained in the internal space contained by them, the size and the speed of the bearing used (for AC For electric motors, the number of poles can also be used instead of speed) to simply calculate the amount of grease.

For the bearing chamber structure with an oil retaining plate (also called an oil slinging plate), the first amount of grease should be appropriately increased, and no grease should be injected into the cavity of the bearing outer cover (this is to accept the "waste grease" that is thrown out "Trash can", the grease in it will not enter the bearing for lubrication, so the newly injected grease will be wasted). With this structure, the grease in the bearing chamber will become less and less. If the grease is not added regularly as required, the lubrication effect will be reduced due to too little grease. Eventually, the grease will dry out due to overheating, causing damage to the entire bearing.

 

3. Things to note

When adding grease, the site should be clean and the tools used should be cleaned with gasoline. After the grease is filled, other components should be assembled as soon as possible to prevent the grease entering the bearing from entraining dust and debris, especially sand and iron filings.

 

4. Grease injection of rolling bearings during operation

For machines using open bearings, after running for a certain period of time, grease should be added to the bearing chamber. For those with an oil filling system, this can be done without dismantling the machine. Otherwise, the bearing cover should be disassembled and oil should be filled directly into the bearing chamber. Care should be taken to use the same brand of grease as the original grease to avoid harmful reactions of greases with different components that may reduce or even lose the lubrication effect, causing overheating damage to the bearing.

Key points of use

 

1. Select grease according to the usage conditions of the machine and the specifications of the bearings. For high-speed machines, grease with low friction coefficient, high wear resistance, high adhesion and low leakage rate must be selected. For machines used in humid environments, it is necessary to choose grease with good waterproof properties.

 

2. Proper cleaning of machines and bearings is a prerequisite for selecting grease. Before adding new grease, the old grease needs to be cleaned to ensure that the old and new grease do not mix together.

 

3. Grease should be added in time according to the usage of the bearing. As the machine is used for extended periods of time, the performance of the grease will gradually decline, and new grease needs to be added in time.

 

4. When adding grease, please ensure that the grease can fully cover the inside of the bearing. If the amount of grease is insufficient, the internal lubrication of the bearing will be insufficient, resulting in abnormal wear during operation.

 

goTop